EVR6-038S Electromagnetic Valve Used In Refrigeration System
|Payment Type:||L/C,T/T,Paypal,Money Gram,Western Union|
|Terms of Trade:||FOB,CFR,CIF,EXW|
|Min. Order:||1 Piece/Pieces|
|Delivery Time:||4-9 Days|
|Productivity:||1200 sets/ 1 week|
|Place of Origin:||Ningbo|
|Supply Ability:||4500 sets/ 1 month|
Model No.: EVR6-038S
EVR6-038S Electromagnetic Valve Used In Refrigeration System
EVR6-038S electromagnetic valve is a direct operated valve or servo valve, suitable for one-way flow. EVR type solenoid valves are used for liquid, air suction or non-steam piping in chillers, cold storage and air-conditioning units.We provide EVR type solenoid valve with various voltage solenoid valves.The clamped solenoid joint valve can be easily installed or removed with a single screwdriver.
Technical Parameters of EVR6 Electromagnetic Valve Used In Refrigeration System:
KV value (m³/h)
SAE inlet/outlet ODF inlet/outlet (Solder) Inch mm Inch mm Inch mm Inch mm Inch mm Inch mm EVR3-014 EVR3-014S 1/4 6 0.5 14 2.8 71 - - 4.0 102 0.3 7 0.27
EVR3-038 EVR3-038S 3/8 10 0.5 14 2.9 73 - - 4.6 117 0.4 10 EVR6-038 EVR6-038S 3/8 10 0.5 14 3.1 79 - - 4.4 111 0.4 10 0.8
EVR6-012 EVR6-012S 1/2 12.8 0.5 14 3.1 79 - - 5.0 127 0.4 10 EVR10-012 EVR10-012S 1/2 12.8 0.6 16 3.1 79 - - 5.0 127 0.4 10 1.9
EVR10-058 EVR10-058S 5/8 16 0.6 16 3.1 79 - - 6.3 160 0.5 12
EVR15-058S 5/8 16 0.7 19 3.4 86 - - 6.9 176 0.5 12 2.6
EVR15-078S 7/8 22 0.7 19 3.4 86 - - 6.9 176 0.7 17
EVR20-078S 7/8 22 0.8 20 3.5 90 - - 7.5 191 0.7 17 5
EVR20-118S 1 1/8 28.8 0.8 20 3.5 90 - - 8.4 214 0.8 22
EVR22-138S 1 3/8 35 0.8 20 3.5 90 - - 11.1 281 1 25 6
EVR25-118S 1 1/8 28.8 1.5 38 5.4 138 2.8 72 10.0 256 0.8 22 10
EVR25-138S 1 3/8 35 1.5 38 5.4 138 2.8 72 11.0 281 1 25
EVR32-138S 1 3/8 35 1.9 47 4.4 111 2.1 53 11.0 281 1 25 16
EVR32-158S 1 5/8 42 1.9 47 4.4 111 2.1 53 11.0 281 1.1 29
EVR40-158S 1 5/8 42 1.9 47 4.4 111 2.1 53 11.0 281 1.1 29 25
EVR40-218S 2 1/8 54 1.9 47 4.4 111 2.1 53 11.0 281 1.3 34
Overall dimension of EVR6-038S Electromagnetic Valve for Refrigeration:
Location of EVR6-038S solenoid coil valve in refrigeration system:
Packing & Delivery of EVR6-038S Electromagnetic Valve Used In Refrigeration:
Types of evaporator in refrigeration system with EVR6-038S Electromagnetic Valve:
When freon liquid of refrigeration system enters expansion valve and is sent to evaporator, it belongs to evaporation process. At this time need to absorb a lot of heat, so that the cooling product temperature gradually reduced, cooling and cooling effect. Then, according to the type of the cooled medium, it can be divided into two types: evaporator for cooling liquid (water) (dry evaporator) and evaporator for cooling air (cooling evaporator).
This paper mainly introduces the evaporator used in the chiller refrigeration system, which is generally dry shell and tube evaporator. The refrigerant evaporates in the tube and water flows on one side of the tube. In order to improve the heat exchange efficiency, a 2mm thick water baffle arranged on one side of the shell tube repays the water around for the purpose of ice brine generation, and the container shell is more than 6mm thick. It is made of Steel Tube and can withstand the pressure of 10kg /cm 2. The heat exchange pipe adopts highly efficient seamless copper pipe, which is processed into internal threaded ribbed pipe by embossing technology, which increases the heat transfer area of the heat exchange pipe, improves the heat transfer performance of the heat exchange pipe, and can withstand pressure of 20 Kg/cm 2. The heat exchange pipe, end plate and expansion pipe are combined, and the end cover is equipped with a partition plate to divide the refrigerant into multiple flows, so that the refrigerant oil reflux. Refrigerant liquid pipe with low pressure valve connection by the work, the total heat transfer coefficient should be able to withstand the fouling coefficient of 0.086 M2 ° C/KW, pressure drop across the evaporator is not more than 6.5 mAq.
Other accessories in refrigeration system with EVR6-038S Solenoid Valve:
1.liquid pipe drying filter
The liquid line drying filter is usually non-removable. Internal use of molecular sieve structure, can remove a small amount of impurities in the pipeline, purification system. The freon refrigerants we use are imported due to the purity of the oxides in the piping during welding and the freon refrigerants. When the drying strainer in the liquid line is blocked, the suction pressure will be reduced and there will be a temperature difference between the ends of the strainer. If this happens, you need to replace the filter.
2.High and low pressure controller
High and low pressure controllers are protective devices in refrigeration systems. High voltage protection is upper limit protection. When the high pressure reaches the set value, disconnect the high pressure controller, loosen the compressor contactor coil, and the compressor stops working to prevent the damaged parts from working under ultra-high pressure. High voltage protection is manual reset. When the compressor starts up again, the reset button must be pressed first. Of course, before restarting the compressor, first of all to check the cause of high pressure, after the elimination of the machine can operate normally.
Low pressure protection is a protection device designed to prevent the refrigeration system from operating under too low pressure. Its setting is divided into high limit and low limit. The control principle is as follows: the low-voltage disconnect value is the pressure difference between the upper limit value and the lower limit value, and the restart value is the upper limit value. The low pressure controller is automatically reset, requiring the operator to constantly observe the operation of the machine. When the alarm should be handled in time to avoid compression captain time frequent stop, affecting the service life.
Welcome to your inquiry!
NINGBO BRANDO HARDWARE CO.,LTD
BRANDO is a professional manufacturer and designer of Solenoid Valve, Solenoid Valve Coil and Solenoid Valve Armature Assembly, located in Ningbo, China. And we can serve customers from various industries. Our company has been producing for more than 10 years, and cooperates with different customers such as oil & gas, chemical industry, water treatment, food & beverage, medical system and so on.
BRANDO maintains its high position in the industrial manufacturing. The advanced lathes and milling machinery are introduced, and from materials procurement to finished product and assembly, it is fully automated and controlled by computers, to improve product quality, and to continuously increase production and delivery efficiency.
BRANDO has fully adopted the ISO-9001 quality management system and introduced the most advanced precision equipment for product inspection, such as digital pressure gauges, computer applications, air leak testers, pressure testers and flow testers.
1. Customized Design and Production: Brando can design and manufacture customized solenoid valves, solenoid coils and solenoid valve armature components to meet your specific needs and applications. We can provide services from small air treatment devices to large fluid systems.
2. Quality Assurance: In addition to designing and manufacturing high-quality products, Brando also provides 100% testing services for all components to ensure that they achieve the best performance under the best performance and to ensure that it runs well in your project.
3. Delivery and After-sales Service: Brando provides large inventory and on-time delivery within 5 to 10 days. We also provide unparalleled after-sales service and 1 year warranty for all products.
1. Solenoid Coil
2. Solenoid Coil Connector
3. Solenoid Valve Armature Assembly
4. Solenoid Valve Timer
5. Brass Solenoid Valve
6. stainless steel Solenoid Valve
7. Plastic Solenoid Valve
8. Refrigeration Solenoid Valve
10. Pulse Jet Valve
11. Valve Diaphragm
12. Pulse Controller
13. Pneumatic Valve
14. Pneumatic Hose Fitting
15. Pneumatic Cylinder
16. Air Filter Regulator Lubricator
17. Pneumatic Actuator Valve
18. Electric Actuator Valve
Focus on your demands, Offer you best solution:
√ Contact us if some points you have doubt
√ Contact us if somewhere need to change
√ Contact us if not the one you are looking for
√ Contact us if you are doing designing
Welcome to your any question and inquiry!
- Company Name: NINGBO BRANDO HARDWARE CO.,LTD
- Representative: Lu Jin Jun
- Product/Service: Solenoid Valve Armatures , Solenoid Valve Coils , Pneumatic Solenoid Valves , Pneumatic Hose Fittings , Pulse Jet Valves , Refrigeration Solenoid Valves
- Capital (Million US $): 1000,000RMB
- Year Established: 2008
- Total Annual Sales Volume (Million US $): US$5 Million - US$10 Million
- Export Percentage: 81% - 90%
- Total Annual Purchase Volume (Million US $): US$1 Million - US$2.5 Million
- No. of Production Lines: 10
- No. of R&D Staff: 5 -10 People
- No. of QC Staff: 11 -20 People
- OEM Services Provided: yes
- Factory Size (Sq.meters): 3,000-5,000 square meters
- Factory Location: Ningbo
- Contact Person: Mr. Brandon Bao
- Tel: 86-0574-83879820
Premium Related Products